![]() ![]() I've only had it for about 2 years at the most. Well I really hope I don't have to replace my good 'ol 780. It just sucks because I have to wait 5 hours to see if I've fixed it or not. Yeah I've made sure it's properly seated and the PCI E connectors are connected. It's just a random occuring event in that case, as it will depend when the system / game / app attempts to use that damaged spot of DDR5 memory from the graphics card (not system RAM). If it's not that, perhaps it's graphic card memory faulty/damaged at a certain point. It might be juice related if occuring at boot. Originally posted by Azza ☠:Take out the graphics card and then reseat it - double checking the PCI-e 12V cables coming from the PSU (Power Supply Unit) to the top of it. I'm using default bios settings and I've had this problem with two different mobos so I doubt flashing is going to help. I even wiped my SSD and put 8.1 back on it. So could it be my RAM or do I have very back luck with buying power supplies?Įven though this is most likely a hardware issue, I've still gone through all the basics - CHKDSK, mem test, check drivers, etc. My GPU temp never goes above 71 degrees Celsius and I have NEVER seen an artifact when gaming. I have used Furmark to stress test my GPU and I play games all the time. So this leaves me to think it's either my GPU or RAM. I've replaced my motherboard and PSU with different ones this week to rule those components out & the problem came back. If I kept my PC on all the time, I wouldn't even be aware of this problem.Īll the components in my computer are new EXCEPT my RAM, GPU, & drives. My computer runs flawlessly, I can play the latest games no problem. If I were to shut down my PC right now and turn it back on, it would boot like normal. Now if I reset or force it off/on it will boot to Windows like normal.Īgain, It only does this if it's been shut down for 5 or more hours. Sometimes when I start my computer up after it's been off for 5 or more hours, it will post but I get all these strange artifacts on my screen(see image) and then it loses signal before getting to Windows. 0967388 Kurtosis 2.395841Edit: after quite a while, did I notice Friedrich' suggestion on a similar verge, i.e, to - reshape long - as well.Image of my problem taken from my phone. reshape long headline underlying, i(id) j(phase) And for the pair of lines for each country, I want red for headline inflation, and blue for underlying, so that they can be distinguished. I already transformed the inflation rates for each country such that for country A, value 1 correspond 0% inflation rate, for country B value 2 correspond to 0% inflation rate, so that the lines for country A will fluctuate around 1, and those for country B around 2, country C around 3, etc. I want to plot on the same graph both types of inflation for a number of countries. ![]() My question is, given the limit on number of arguments, is there a way to assign one color to lines of Set1 and another color to lines of Set2.įor illustration, the Set1* lines are headline inflation, and Set2* lines are underlying inflation. Xsize(10) ysize(20) xlabel(#10) ylabel(1(4)14, labsize() tlength(zero) glwidth(vvvthin) glstyle(dot) glcolor(black)) ytick(none) ymlabel(none) Subtitle(,size(small)) tlabel(,format(%tCHH) labsize(vsmall)) legend(off) ytitle("") xtitle("") title("") /// Lcolor (red red red red red red red red red red red red red red blue blue blue blue blue blue ) /// Graph twoway tsline Set1A Set1B Set1C Set1* Set2A Set2B Set2C Set2*, /// You might look into "pstyles".Thanks Doug. ![]() It would help to have the code you are starting from, to better understand the organization of the data you are starting from, and the graph you hope to end up with. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |